 |
|
DSP emulator for Euro 100,--
Low cost Spectrum Digital Emulator for TI DSP's now starting at Euro 100,--. This system supports the TI Digital Signal Processors and the Code Composer Sudio toolsuite.
Low cost Spectrum Digital Emulator for TI DSP's
Hardware Features :
* Supports Texas Instruments Processors and Microcontrollers with JTAG interface:
... |
| |
|
|
Spectrum Digital DSP Emulators Overview
The Spectrum Digital JTAG emulators shown below provide the interface between the development software (Code Composer Studio or SDFlash) running on the host computer and the DSP. The JTAG emulators provide a choice of interfaces to the host processor (parallel port, USB, and PCI). The emulators shown below can be used to the following device families: VC33, C3x(*), C4x, C2000, C5000, C6000, ... |
| |
|
|
XDS560R JTAG Emulator
The XDS506R USB JTAG Emulator supports Texas Instruments Digital Signal Processors and Microcontrollers with JTAG interface (F28xx, C54xx, C55xx, C6xxx, DaVinci™, TMS470 ARM9, OMAP). It is compatible with XDS560 from Texas Instruments. Is powered by a PSU which is included. Supports USB 2.0, no adapter card is required.Advanced emulation controller provides high performance.Compatible with + ... |
| |
|
|
XDS 510 USB
One of the new generation of USB emulators, the XDS510-USB shares all the advantages of a flexible, hot-plugable, external, bus-powered emulation solution. The use of an advanced emulation controller gives the XDS510-USB much improved download speeds as compared to other USB emulators. The XDS510 USB will work with Spectrum Digital’s Flash Programming and SDConfig Utilities. Both of these ut ... |
| |
|
|
XDS510 USB Galvanic
The XDS510 USB Galvanic offers the same features as the XDS510 USB plus voltage isolation between the emulation hardware and the DSP target system. Its use will be beneficial in developing applications such as motor control, power supplies, industrial control, and automated test equipment. The XDS510 USB Galvanic will work with Spectrum Digital’s SDFlash Programming and SDConfig Utilities. B ... |
| |
|
|
XDS510 USB PLUS
XDS510 USB PLUS USB JTAG Emulator
The XDS510 USB PLUS offers the same featires as the well known XDS510 USB, however boasts higher performance. The XDS510 USB PLUS features: low voltage JTAG Interfaces, 1.8Vto 5V, ARM style adaptive clocking support, programmable Tclock frequency up to 32MHz, USB bus powered, no external power supply required, compatible with USB 1.x ... |
| |
|
|
XDS510 PP-PLUS JTAG Emulator
The XDS510PP PLUS JTAG Emulator is a low-cost replacement for the XDS510 Emulator from Texas Instruments. An external emulator it connects to the PC via the parallel port. It supports TI Digital Signal Processors and Microcontrollers with JTAG interfaces (IEEE1149.1). The emulator can be powered from the target via the JTAG PD pin, or from the power supply provided, and can operate with both 5V an ... |
| |
|
|
XDS510 PP-PLUS MPSD JTAG Emulator
A simple low cost portable parallel port based MPSD emulator.
FeaturesSupports Texas Instruments Digital Signal Processors with the MPSD interface (C3X)Compatible with XDS510 from Texas InstrumentsOperates with parallel port on PC or laptop, no internal adapter requiredSupports 4 bit, 8 bit, and EPP transfersCompatible with 3.3V or 5V processorsPowered by target or supplied adapterCompa ... |
| |
|
|
SPI525 JTAG Emulator
SPI515 Parallel Port Variable Voltage JTAG Emulator
Description
The SPI515 is an external parallel port based emulator that automatically adjusts to the voltage level of the logic that it will be controlling, from 1V to 5V. It is designed to be compatible with the existing Texas Instruments XDS510 emulator and operate with the Code Composer and Code Composer Studi ... |
| |
|
|
SPI530 Intelligent MPSD Emulator
SPI530 Intelligent MPSD Emulator
Description
The SPI530 Intelligent MPSD Emulator supports Texas Instruments TMS320C3x Digital Signal Processors with MPSD interface. Provides highest performance with internal high speed control processor is compatible with XDS510 ISA MPSD emulator from TI. Operates with parallel port, no internal adapter card re ... |
| |
|
|
SP110LV Opto-isolating JTAG POD
The SPI110LV provides up to 2500 volts RMS isolation between the target side and the emulator side of the pod. Two benefits of this are safer operation on "HOT" designs and the reduction of common mode noise problems which can cause scan errors on non-isolated emulators.
FeaturesProvides optical isolation of JTAG signals allowing debugging of high voltage applications (m ... |
| |
|
|
Low Voltage adapter for JTAG DSP Emulator
The low voltage adapter for JTAG Emulators provides voltage translation between +3.3 volt emulator interface and TI JTAG targets that require down to +1.8 volt interfaces. It is compatible with XDS510 USB and XDS510PP Plus JTAG Emulators from Spectrum Digital and Code Composer Studio and standard 14 JTAG header from TI. The adapter is powered by the target board and the maximum current drawn from ... |
| |
